A few minor updates to Chapter 2 text

src/start/hardware.md

@@ -93,7 +93,7 @@ $ cargo build --example hello
 Debugging will look a bit different. In fact, the first steps can look different
 depending on the target device. In this section we'll show the steps required to
 debug a program running on the STM32F3DISCOVERY. This is meant to serve as a
-reference; for device specific about debugging check out [the
+reference; for device specific information about debugging check out [the
 Debugonomicon](https://github.com/rust-embedded/debugonomicon).
 
 As before we'll do remote debugging and the client will be a GDB process. This

src/start/registers.md

@@ -6,7 +6,7 @@ You may well find that the code you need to access the peripherals in your micro
 
 * Micro-architecture Crate - This sort of crate handles any useful routines common to the processor core your microcontroller is using, as well as any peripherals that are common to all micro-controllers that use that particular type of processor core. For example the [cortex-m] crate gives you functions to enable and disable interrupts, which are the same for all Cortex-M based micro-controllers. It also gives you access to the 'SysTick' peripheral included with all Cortex-M based micro-controllers.
 * Peripheral Access Crate (PAC) - This sort of crate is a thin wrapper over the various memory-wrapper registers defined for your particular part-number of micro-controller you are using. For example, [tm4c123x] for the Texas Instruments Tiva-C TM4C123 series, or [stm32f30x] for the ST-Micro STM32F30x series. Here, you'll be interacting with the registers directly, following each peripheral's operating instructions given in your micro-controller's Technical Reference Manual.
-* HAL Crate - These crates offer a more user-friendly API for your particular processor, often by implementing some common traits defined in [embedded-hal]. For example, this crate might offer a `Serial` struct, with a constructor that takes an appropriate set of GPIO pins and a board rate, and offers some sort of `write_byte` function for sending data. See the chapter on [Portability] for more information on [embedded-hal].
+* HAL Crate - These crates offer a more user-friendly API for your particular processor, often by implementing some common traits defined in [embedded-hal]. For example, this crate might offer a `Serial` struct, with a constructor that takes an appropriate set of GPIO pins and a baud rate, and offers some sort of `write_byte` function for sending data. See the chapter on [Portability] for more information on [embedded-hal].
 * Board Crate - These crates go one step further than a HAL Crate by pre-configuring various peripherals and GPIO pins to suit the specific developer kit or board you are using, such as [F3] for the STM32F3DISCOVERY board.
 
 [cortex-m]: https://crates.io/crates/cortex-m
@@ -73,7 +73,7 @@ pub fn init() -> (Delay, Leds) {
 
 ```
 
-We've access the `PWM0` peripheral in exactly the same as as we access the `SYST` peripheral earlier, except we called `tm4c123x::Peripherals::take()`. As this crate was auto-generated using [svd2rust], the access functions for our register fields take a closure, rather than a numeric argument. While this looks like a lot of code, the Rust compiler can use it to perform a bunch of checks for us, but then generate machine-code which is pretty close to hand-written assembler! Where the auto-generated code isn't able to determine that all possible arguments to a particular accessor function are valid (for example, if the SVD defines the register as 32-bit but doesn't say if some of those 32-bit values have a special meaning), then the function is marked as `unsafe`. We can see this in the example above when setting the `load` and `compa` sub-fields using the `bits()` function.
+We've accessed the `PWM0` peripheral in exactly the same way as we accessed the `SYST` peripheral earlier, except we called `tm4c123x::Peripherals::take()`. As this crate was auto-generated using [svd2rust], the access functions for our register fields take a closure, rather than a numeric argument. While this looks like a lot of code, the Rust compiler can use it to perform a bunch of checks for us, but then generate machine-code which is pretty close to hand-written assembler! Where the auto-generated code isn't able to determine that all possible arguments to a particular accessor function are valid (for example, if the SVD defines the register as 32-bit but doesn't say if some of those 32-bit values have a special meaning), then the function is marked as `unsafe`. We can see this in the example above when setting the `load` and `compa` sub-fields using the `bits()` function.
 
 ### Reading
 
@@ -95,7 +95,7 @@ pwm.ctl.write(|w| w.globalsync0().clear_bit());
 
 ### Modifying
 
-If we wish to change only on particular sub-field in this register and leave the other sub-fields unchanged, we can use the `modify` function. This function takes a closure with two arguments - one for reading and one for writing. Typically we call these `r` and `w` respectively. The `r` argument can be used to inspect the current contents of the register, and the `w` argument can be used to modify the register contents.
+If we wish to change only one particular sub-field in this register and leave the other sub-fields unchanged, we can use the `modify` function. This function takes a closure with two arguments - one for reading and one for writing. Typically we call these `r` and `w` respectively. The `r` argument can be used to inspect the current contents of the register, and the `w` argument can be used to modify the register contents.
 
 ```rust
 pwm.ctl.modify(|r, w| w.globalsync0().clear_bit());